Clear acrylic display cases are some of the guidelines on how to show your collectables, models, miniatures or similar items while protecting them from dust. However, one of several issues with acrylic photo frames is that they tend to are available in standard sizes as well as your item might not exactly fit well inside of a regular-sized case. You are able to solve this problem if you make a custom case that was designed to show your item in the simplest way possible.
1.Study the item you want to display. A display case must be a minimum of 2 inches greater than the goods in height, width and length. For instance, for those who have one car that is certainly 5 inches long, 3 inches wide and 3 inches tall, your case ought to have two side panels which can be 7 inches by 5 inches, two side panels which can be 5 inches by 5 inches and a top panel which is 7 inches by 5 inches. Calculate the size of your case and write down the size and style of all the panels you need. Make amends for the width of your acrylic sheet by adding extra width to the top panel that is certainly twice the thickness in the acrylic sheet.
2.Cut your acrylic sheet into panels, employing a table saw having a blade for cutting acrylic, a circular saw, saber saw, jigsaw or a handsaw. Move the sheet steadily with the blade, if you use a table saw. Acrylic sheets come with a protective covering; leave this on when you cut the panels.
3.Sand the edges of the acrylic panels. Start out with a 120-grit sandpaper, then relocate to 220-grit. Finish the sides having a fine, 400-grit sandpaper. Use up to a 600-grit sandpaper for the very smooth finish. Use wet sanding and rinse the sandpaper often. Buff the edges using a buffing wheel attachment for the drill, if desired. Peel off the protective coating when you have finished.
4.Hold the sides of your case together to produce 90-degree angles, using angle clamps. Seal the outer seam between the acrylic box, using masking tape.
5.Apply solvent cement down the inner seams in the case. Use cement with a needle-nose applicator, if you can. Glue one-50 % of the truth at a time as being the seams must be horizontal to avoid the glue from running out. Wait about 30 minutes for that solvent cement to dry before gluing another side.
6.Set the top panel on top of your case and seal the outer seams between this panel and the remainder of the case with masking tape. Turn the complete case over to ensure the top panel is on the bottom. Apply solvent cement into the seams. Await it to dry.
7.Cut a piece of wood so it is precisely the same size as the top of your case. This can be the foot of the case. Ensure that the wood that is certainly between 1/2 inch and 1 inch thick.
8.Cut four bits of trim. For example, use quarter-round molding, if desired. Make sure that two pieces are definitely the width of the box plus twice the width in the trim itself. Cut another two pieces the length of the situation plus twice the width from the trim. Miter the edges of each and every piece so that they will fit together at 90-degree angles.
9.Glue the components of trim round the edges of the wood which you cut for the bottom of the way it is, using wood glue. Permit the glue to dry. Sand, then stain or paint the wood. Seal the base with 97dexfpky coat of polyurethane or similar sealer. Allow it to dry. Placed the acrylic cosmetic display across the wooden base.
Should your acrylic sheets are 1/8 inch thick, you are able to score and snap the pieces apart rather than cut them a saw. However, sheets this thin will be too flimsy for anything but a really small case.
For additional security, also you can glue the seams externally from the case once the inner seams have dried. Use masking tape again on the inner seams to avoid the glue from running.
Tend not to apply excessive solvent cement. The glue will likely be drawn between the panels, therefore you only need some.
It is actually entirely possible that the blade to melt the plastic when you move the acrylic too slowly or too quickly through the table saw.
Use caution when utilizing power tools. Wear goggles to protect the eyes when cutting, sanding or filing materials or when working with solvent cement.